compustar cm3000 program manual

compustar cm3000 program manual

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:CAUTION: Changes or modifications not expressly approved by the partyPage 4Your Warranty. The product s warranty is automatically void if its date code or serial number is defaced,Important Information. Congratulations on the purchase of your high-tech vehicle security system and remoteDue to the complexity of the system, it must only be installed by an authorized. CompuStar dealer for full warranty and technical support. Installation of this product byThe owner s guide should help you to get the most out of your system. Please takeAdditional replacement copies of thisPlease verify if the opening of any door orIf any of the doors or hatchback is notDo not set Reservation Mode when the window(s) are open or if there is anyoneSystem Maintenance. This system requires no specific maintenance. Your remote-pager is powered by a single. AA battery that will last approximately one month under normal use depending on theThere is a battery icon in the lower right corner of the. CompuGLO LCD indicating remaining battery life. When the battery weakens, theContact yourSafety Information. Please take these safety precautions under the following conditions:When servicing (i.e. changing the oil, washing your car) your automobile, the CompuStarThere is a safety shutdown switch under the hood thatHowever, if the switch hasButton II is pressed for 2 seconds even if the hood is open.Whenever you loan your vehicle to an individual who is not familiar with Compustar,This will prevent the vehicle loaner from accidentally activating the CompuStar auto-security system. The model name, 2WSSR, stands for Two Way Spread Spectrum Remote with. Liquid Crystal Display. This 5-channel transmitter that allows you to activate multipleCompuGLO color LCD (Liquid Crystal Display).http://drddvichitra.com/userfiles/brother-fax-mfc-7360n-manual.xml

• compustar cm3000 program manual, compustar cm3000 program manual pdf, compustar cm3000 program manual download, compustar cm3000 program manual free, compustar cm3000 program manual instructions.

The remote-pager comes with CompuGLO which is a unique color LCD display thatIf the Compustar 2WSSR is installed in a manual transmission vehicle, extra precautionsPage 3. Page 4Icon. Shock. Turbo. Timer. Passive. Explanation. Indicates if the Shock Sensor is on or off. See page 12. Indicate if Turbo Mode is on or off. See page 17. The user can activate differing functions of CompuStar 2WSSR system by pressing. Compu Star remote-pager. Channel. Indicates if Passive Arming Mode is on or off. Button. Indicates that the second stage shock sensor has been triggered. If the icon appears continuously, you are in mute(vibration) mode. If theSee page 15. Indicates if Timer Start Mode is on or off. See page 16. Press for. Function. Factory. SettingIndicates if your car parking lights are flashing.Indicates that your car siren is turned on or off when you lock orPanic Mode. Indicates that someone is paging you from your vehicle. OnIndicates if you are in Valet Mode. See page 15. Displays if your car is locked or unlocked. Indicates if your remote-pager is transmitting signals to the controller unit. Displays remaining battery life.On. Displays if your door is open.Off. Displays if your vehicle has auto-started properly or ignition on.Programming Menu 1. Displays if your trunk is open.Programming Menu 2. Page 5. Page 6Ground. An Aux output is a 5sec pulse that can be changed to Latch. See Programming Options.Rx Antenna Data CableStarter Kill supplies a negative 250mA output when the system is armed. Dome Light Supervision: Dome light is turned on for one minuteViolet wire of CN2 supplies a ground pulse before Lock. The Dome Light Rearm Option is to simulate opening the doorThe sequence for the Rearm pulse: pulse when armed (locked). The sequence for the Disarm pulse: a pulse when disarmed(unlocked). Installation of FM or SS Antennas and RPS. The antennas have been calibrated forPage 8The car will chirp once indicating that you are in programming mode.http://feyzullahalpman.com/userfiles/brother-fax-manual.xml

You will hear a chirp and see the parking lights flash eachStep3: Wait a few seconds. You will hear a number of chirps and see aIf the number of chirps or flashes is notStep4: Press Button I for the default factory settings and your car willPress Button II for theIf you hear a long chirp, you are going out of programming mode,Option Programming for Six Button(ONE WAY) Remotes. The procedures will be same as the 4 button remotes except the use of theProgrammingProgramming Menu 1. Programming Menu 2. Option SelectionLockUnlockStep2: Press Button III three times. This is confirmed by a car chirp andA few second later,Your car is now set to all of the original factory default settings. Optional. Factory Default. Setting - Button I Setting - Button II. FeatureA second unlock pulse is need to unlock the rest of the car doors. Page 9. Page 10Isolate the driver?Call us for the technical support if you are notButton. Siren. Installation required. Starter Kill. Panic Mode. IV for 2 secondsStarter-Kill. Activated immediately. Anti-Jacking Mode. IV for 2 secondsIgnition-Kill. Ignition Kill. Activated immediately if key is not on. If key is on, activated in 30 seconds afterFeature. Programming. Setting - Button I Setting - Button II MethodAnti-jacking. Ignition Controlled Door Lock. Aux 1 Output. Aux 2 Output. Siren Duration. FeatureChannnel Expander. Passive Locking, too No Passve Locking RemoteLatchLatchMethod. Non using of Channel Using of Channel. Expander module Expander module Option. Programmer. When Option 2-9 is on. Non using of Passive Using of Passive (CM3 -Series). Mode with remote Mode with remote. NoteThe differences between Panic mode and Anti-Jacking mode are. Page 11. You can program the duration between 1 to 99 seconds. You can program the “Latch Mode” also.ContentsOff. PluseLatch. OnChannel Expander for 7 Aux outputs. If you take this Channel Expander optionRefer to the manual of the Channel Expander.

The Passive setting of the remote will no longer work as the Passive ArmingPage 12AUX No.Access to passive mode through a remote. Non setting of passive mode Setting of passive modeButton I. Button IIButton II. Button IIIOutput. All outputs are connecting with. Channel Expander through AUX1.In order to decrease the chirping volume of the siren, cut the loop located onAdjusting the Shock Sensor Sensitivity. In order to the shock sensor sensitivity, turn the screw located on theTurning the screw just a small amount canPage 13. Page 14PDF Version: 1.3. Linearized: No. Page Count: 8. Creation Date: 2006:11:22 04:58:35Z. Mod Date: 2006:11:22 04:58:35Z. Producer: Acrobat Distiller 5.00 for Macintosh. Author: mac1. Metadata Date: 2006:11:22 04:58:35Z. Creator: mac1. Title: MA510. This is the sequence: 1. Remote Start unit receives signal This wire serves two functions: 1. To engage Reservation Mode for manual transmissions, reference the users or install guide. 2. To activate the Turbo Timer, reference the users or install guide. This wire serves two functions: 1. It prevents tIn some cases you may have to go to the ECU or Coil pack. 3. The Voltage will read (AC), so you will need to set you meter accordingly. 4. With the vehicle off the voltage should read 0.00 AC. 5. Start the vehicle and at this time the voltage should fluctuate between 1 and 8 voltsPlease note: Timed pulse durations can only be programmed with the CompuProgrammer. It can be programmed for a timed pulse or latch. Please note: Timed pulse durations can only be programmed with the CompuProgrammer.Once you have found the correct wire simply press this button while the vehicle is running and the siren will chirp once to confirm that the tach is learned. If the Siren chirps three times the tach source is not valid. If the switch is set to. CM3 SERIES User Manual Download Like Full screen Standard Page of 80 Go CM3 SERIES Page 1: Master Install Guide By:Install Checklist.Page 4.

Remote Programming ProcedurePlease use this checklist to complete the installation of any CompuStar system. ThesePage 5 Remote Programming ProceduresBecause the CompuStar systems are modular in design (upgradeable), the remotes Do. Not come pre-programmed from. Page 8 Programming for:However, 1 one-CompuStar antennas can, in general, be mounted with any orientation. Horizontal orThis wire is only present in international models. This jumper wire will determine thePage 16 - 16 -Page 20: CONNECTOR 1 CM-3000 WIRING DETAILThis is an optional input that willPage 23: (Pre-wired L.E.D.) Pin 6 Not used.This is an optional. Page 24: (Optional Temperature sensor) CONNECTOR 7Pin 1 Black-Shock sensor (-) negative ground input. Pin 2 White-Shock sensor 2nd stage. Page 25: (Pre-wired Antenna Cable) CONNECTOR 11Pin 1 Yellow-RX input. This wire receives signal from remote. Pin 2 White-TX output. Page 26 - 26 -This wire must be connected to the vehicles ignition toPin 1 Not used. This wire will provide. Page 31: (Pre-wired Antenna Cable) CONNECTOR 7Pin 1 Black-R.P.S. sensor (-) negative ground input. Pin 2 White-R.P.S. Page 32 - 32 -Page 34: CONNECTOR 1 CM-4200 WIRING DETAILThis input is required to shutThis wire will provide a (-) negativeThis input is used for ignitionPage 46 menu that you would like to change, you would press the (trunk), andPage 49 1-Way 4 Button RemotesLock After Remote Start.Page 56 the lock and rearm pulses to the vehicle while the dome light output is active. ThisIf the OptionPage 60 - 60 -I have everything hooked up, but the system still doesn’t do anything.Page 65 Common Diagrams. Reverse Polarity Door LocksTransponderNote: This diagram will not work with all turbo timers.Using the Ground While Armed OutputThe channel expander is an add-on module that can be used to expand the existing twoPage 80 temperature (Between -22 and 32 degrees fahrenheit). If started, the vehicle will run for. That's okay. For some sites, we do too.

However several sections and features of our Please consider disabling your ad blocker on our site and help support Thanks in advance! I replaced with a new battery and the remote still not working. I left the key in the car and remote started, the engine cranked but the car won't start either. Does the vehicle stay running with the remote starter?Where are you getting the tach signal from. Check the connection and relearn tach.The vehicle stays running with the remote starter. Start the car with the key, hold your foot on the brake, then press and hold the remote start button for roughly 3 seconds. The parking lights should flash once to confirm the signal was read. KennyThe car siren will chirp once to confirm the tach was learned. If the siren chirps 3 times, you have the wrong tach wire. Soldering is fun! I think you are correct. My bad. KennyNOTE: You must use the BLACK master key to complete the programming procedure. Then, hold a working ignition key right up against the ignition cylinder and try a remote start. ( You could also insert the key fully but not turn it. ) If it now starts, the 556H is bad. Soldering is fun! This topic is closed. Any user assumes the entire risk as to the accuracy and use of this information. Please. Page 4Page 6Page 7Page 7Page 8Page 9Page 13. Page 3. Notes. Wiring DiagramRxKnock CN9Tach Learning Switch. Antenna. Temp Sensor. Remote Paging. System. Optional SensorRedEngine SensingBlue. NoneViolet. Brown. White. Yellow. NoneFutu re UseWhite. Red. YellowR elay fo r 2nd Ig, Acc or Star terBk. Gr. JumperOne is to supply power to the CPU and Ignition and the other is to supplyOne for Starter-kill and the other forMost emergency brakeLikewise, if the positive glow plug wire sees positive, the remote startingThere is no programming forDome light is turned on for one minute after unlock. Page 4.

If you program Dome Light Rearm option, The Violet wire of CN5The Dome Light Rearm Option is to simulate Opening the door andThe next step is to press the black tachometerIf the siren chirps 3 times, you have the wrong tach wire.When tested with your meter, it should show you less than 5V whenWhen the vehicle is started, the wire should read between 9V to 14V.If the car siren chirps 3 times, there is a problem with the tachometerInstallation of AM, FM or SS AntennasDifferent installation mayOption Programming for Four Button Remotes. Error Number. Tach Learning Error DignosisFind a different wire. Switch and Jumper Settings. Dip. Jumper Wire. Switch. On Uncut: Manual Transmission. Tach Sensing 25 min run time (45 min diesel). Cut: Automatic Transmission Alternator Sensing 15 min run time (25 min diesel). Off. Important! Installation of AM, FM or SS Antennas. Once you cut the Jumper Wire, you are not allowed to reconnectPage 6. The car will chirp once indicating that you are in programming mode.You have to hear a chirp and see the parking light flashStep3: Wait a few seconds. You will hear a number of chirps and see aStep4: Press Button I for the default factory settings and your car willPress Button II for the optionalPage 7Remote-Pager Programming Menu Options. If you want to change more options, go back to Step1.This will be. FeatureYou will be confirmed by a car chirpPress button III third time. You will be confirmedA few second later, your car willUnlock Before, Lock After Starting. Lock after remote startAlternator SensingDouble Pulse UnlockMethod. Diesel Preheating TimeOption. ProgrammerProgramming. MethodStep2: Press button III once. This will be confirmed by a car chirp and. Setting - Button I Setting - Button IIOption Programming for Six Button(ONE WAY) Remotes. Note.

The procedures will be same as the 4 button remotes except the useActivating this feature will unlock the vehicle for a brief second in order toA second unlock pulse is need to unlock the rest of the car doors. ProgrammingProgramming Menu 1. Option SelectionLockUnlockImportant! In order for this feature to operate, the i nstaller must use the. Isolate the driver’s door actuatorCall us for the technical suppor t if you are notPage 9With this mode, engine willIgnition Kill. Method. FeaturePassive Arming. Anti-jacking. Siren DurationPassive Arming with the. Channnel Expander. Passive Locking, too No Passve Locking RemoteLatchLatchIn the default factory setting, Cold Sensor input works as Remote Start. Activation Input. A Ground pulse to this wire will start the vehicleThe differences between Panic mode and Anti-Jacking mode are. If key is on, activated in 30 secondsIn addition, the vehicle will automatically unlock the doors upon pulling theThis option must be chosen at the time of installation. Manual Transmission Vehicle or Turbo Mode: This Programmable optionContentsMethod. Page 10. IV for 2 seconds. SirenInstallation required. Starter-Kill. Activated immediatelyOff. PluseLatchLatch. OnPluseYou can program the duration between 1 to 99 seconds. You can program the “Latch Mode” also.Channel Expander for 7 Aux outputs. If you take this Channel Expander optionNu4000R operate these 7 outputs instead of normal button functions such as. Refer to the manual of the Channel Expander. Page 11The Passive setting of the remote will no longer work as the Passive ArmingSetting. AUX No.Button I. Button III. If there is a problem in auto-starting your car, you will hear three chirps whenWait for 2 seconds and the cause for the error will be indicated by the numberError NumberAccess to passive mode through a remote. Non setting of passive mode Setting of passive mode. Diagnosing Problems with Auto-StartError Reason. Engine On. Key On. Door Open. Trunk Open. Brake On. Hood Open.

Reservation OffButton IVAll outputs are connecting with. In order to the shock sensor sensitivity, turn the screw located on theTurning the screw just a small amount canPage 12. Page 13. Page 14. Page 15.